Booster Pump Stations: Turnkey Pressure Boosting
Cascade of 2-6 pumps, hydraulic accumulator, frequency drive, control cabinet with switching logic and protections. Complete factory assembly on a common frame - arrived, connected the input / output and power cable, after 1 day it works. We select the operating point Q/H, the real consumption schedule (daily and seasonal unevenness), network pressure restrictions and the need for backup. We work with European, Italian, Turkish manufacturers.
How to select a booster station
The architecture of the station depends on the schedule of consumption, the responsibility of the object and the budget. One universal option does not exist.
What is needed for the calculation
Consumption and pressure
| Estimated consumption | m³/h, taking into account the coefficient of unevenness (1.5-3 for housing, 1.2-1.5 for production). |
| Minimal consumption | m³/h at night or during downtime. Determines the volume of the hydraulic accumulator and the logic of stopping the leading pump. |
| Head pressure | bar to be maintained in the network. Usually 4-6 bar for domestic supply. |
| Inlet pressure | bar from the city network or from the tank. The difference between the head and the inlet is the real selection of pumps. |
| Geodetic elevation | m, from the station level to the upper consumption point. Building height × 0.1 bar per floor. |
Electricity and construction
| Voltage | 3×400 V, power 1.1-22 kW per pump for typical stations. For large ones - up to 75 kW. |
| Type of pumps | Multi-stage vertical (CR-series, MVI, MXV) — standard. Horizontal monoblocs are less common. |
| Material of the flow part | SS304 is the drinking water standard. SS316 — for marine or high chloride. |
| Collectors | Hot-dip galvanized steel, stainless SS304 for responsible, SS316L for CIP with hygienic flanges. |
| Control cabinet | IP54, with Danfoss / Schneider / ABB UPS, soft start, touch screen control panel. |
How a station with a frequency drive works
Modern booster station the pressure switch does not start or stop the pump— it keeps the pressure smoothly due to the change of revolutions. The flow pressure sensor continuously measures the actual value. The PLC in the cabinet compares it with the set point (setpoint, for example 5.0 bar) and issues a command to the frequency drive to speed up or slow down the rotation of the pump. Reaction time — 0.5-2 seconds, retention accuracy — ±0.05-0.1 bar.
When the consumption increases (in the morning, at the peak), the leading pump reaches maximum speed. If the pressure still drops, the PLC starts the second pump (on a state of emergency or with a contactor). The third, fourth — according to the same principle. When the flow drops, the pumps stop in sequence, the latter reduces the revolutions to the minimum. In the night idle mode, the pressure is maintained by the hydraulic accumulator, the pumps are completely stopped.
Alternating logic: the leading pump is changed by the number of hours or hours. This is critical for even wear — otherwise one pump has 30,000 hours, the others 200. The rotation is set up in the cabinet and done automatically.
Emergency scenarios: emergency failure — transition to direct start from the pressure switch. Pressure drop at the inlet (dry running) — stop of the station with alarm. Excess pressure on the head (jammed valve) - instant stop with an accident. Overheating of the engine (according to the temperature sensor) - stopping this pump while continuing the operation of others.
Typical Applications
What is Actually Ordered in Ukraine
Compare configurations by operating parameters, materials, compatibility and scope of supply. Establish purchase-price and operating-cost differences from quotations based on the same requirements.
For fire protection systems in Ukraine, the standard is certified implementation of EN 12845 with a test run once a week. This is a separate class of equipment with a reinforced frame, redundant sensors and often with a backup diesel pump. There are few manufacturers in the world that hold full certification - mostly large European brands.
Compare configurations by operating parameters, materials, compatibility and scope of supply. Establish purchase-price and operating-cost differences from quotations based on the same requirements.
What destroys a booster station in 6-12 months
- An undersized hydroaccumulator without a state of emergency. Cascade ON/OFF with an 80 l tank at a 30 m³/h station — the pumps start every 30-60 seconds. Seals die in 6-9 months instead of 5-7 years. Either take the emergency vehicle on the driver, or a 300+ liter tank.
- Lack of protection against dry running. A drop in pressure at the inlet to 0 — and the pump spins with an empty casing, overheats in 3-5 minutes. Protection is implemented by a pressure switch at the inlet or a level sensor in the tank. Necessarily.
- One pump without reserve. If the station is critical for the house or production, the lack of a reserve is a guaranteed downtime at the first accident or service. The N+1 standard for all responsible applications.
- Incorrect setpoint setting. Excessive pressure (for example, 7 bar instead of the required 5) — constant overspending of electricity by 20-30%, accelerated wear of seals, water hammer in the pipeline. Fine-tuning is a mandatory stage of commissioning.
- Lack of overvoltage protection. A thunderstorm or a throw in the network destroys emergency equipment (cost 500-2500 USD per one) and engines. A surge arrester in the entrance panel costs 50-200 USD — it is paid for by the first accident.
- Cabinet without emergency alarm. An accident happened - no one knows. It was discovered in the morning due to a complaint from residents. Simple 6-12 hours. Integration with a GSM modem or SCADA solves the problem in minutes.
FAQ before ordering
How many pumps in a cascade?
Working + 1 reserve. For floors 9-16 — 3+1. For high-rise buildings and commercial buildings — 4+1 or 5+1. Less than 2 is not a station. More than 6 - difficulty > benefit.
Emergency on all or on one?
The financial benefit depends on the duty cycle, load profile and existing equipment. A comparison requires operating parameters, annual running hours and site conditions. Calculate consumption and payback for the agreed configurations.
What is the volume of the hydraulic accumulator?
With state of emergency — 24-80 l. Without state of emergency — 200-500 l at 10-30 m³/h, otherwise the pumps die within a year.
Factory assembly or on-site?
Compare a factory-built station with a custom equipment package by duty points, redundancy, dimensions, controls and maintenance access. The chosen configuration must suit the connections and site conditions.
What are the protections in the cabinet?
Current, phases, dry run, maximum pressure, surge. For engines >15 kW — thermal sensors. For fire fighters, there is a test run once a week.
How long until DAP?
Standard CR/CRE with 3-4 pumps — 6-10 weeks. Special performance — 12-16 weeks. Polish analogues from the warehouse - 2-4 weeks.
Inputs for an accurate equipment selection
Start with these details. Mark any unknown requirement in your enquiry so it can be clarified before a model is selected.
Check the full order code, contents, technical compliance, exclusions, documents, warranty terms and lead time in the offer. Price and availability are confirmed for your order.
Prepare an equipment enquiryThe form opens with the topic and your checklist. Nothing is sent until you submit it.